Journal of Engineering Materials and Technology 2004 - Abstracts

Journal of Engineering Materials and Technology 2004
TitleSubjectAuthors
A comparative study on various ductile crack formation criteria.Science and technologyBao, Yingbin, Wierzbicki, Tomasz
A comparison of two self-consistent models to predict the cyclic behavior of polycrystals.Science and technologyAbdul-Latif, A.
A hybrid approach for quantifying the winding process and material effects on sheet coil deformation.Science and technologyCao, Jian, Li, Shunping
An assessment of in-service stress relaxation of a work-hardened aluminum magnesium alloy.Science and technologyZhu, L., Beaudoin, A. J., MacEwen, S. R.
Application of multiscale crystal plasticity models to forming limit diagrams.Science and technologyMcGinty, Robert G., McDowell, David L.
A simplified approach to estimate limiting drawing ratio and maximum drawing load in cup drawing.Science and technologyDaw-Kwei Leu, Jen-Yu Wu
A slip-based model for strength evolution during cyclic loading.Science and technologyTurkmen, H. S., Miller, M. P., Dawson, P. R., Moosbrugger, J. C.
Assessment of tensile residual stress mitigation in alloy 22 welds due to laser peening.Science and technologyRankin, Jon E., Hill, Michael R., DeWald, Adrain T., Lee, Matthew J., Chen, Hao-Lin
A study of inhomogeneous plastic deformation of 1045 steel.Science and technologyJiang, Yanyao, Zhang, Jixi
A study of thermal fracture in functionally graded thermal barrier coatings using a cohesive zone model.Science and technologyRangaraj, Sudarshan, Kokini, Klod
A two-property yield, failure (fracture) criterion for homogeneous, isotropic materials.Science and technologyChristensen, Richard M.
Bilinear behavior in nano and microindentation tests of fcc polycrystalline materials.Science and technologyElumustafa, A. A., Ananda, A. A., Elmahboub, W. M.
Combined edge and anisotropy effects on Fickian mass diffusion in polymer composites.Science and technologyHamidi, Youssef K., Aktas, Levent, Altan, M. Cengiz
Creep behavior of Al-Si die-cast alloys.Science and technologyLakes, Roderic, Jaglinski, Tim
Deformation mechanisms of very long single-wall carbon nanotubes subject to compressive loading.Science and technologyBuehler, Markus J., Gao, Huajian, Kong, Yong
Dynamic compressive behavior of EPDM rubber under nearly uniaxial stain conditions.Science and technologyChen, W., Song, B.
Effect of bond thickness on the fracture toughness of adhesive joints.Science and technologyIkeda, Toru, Miyazaki, Noriyuki, Lee, Deok-Bo, Nak-Sam Choi
Effect of geometry and materials on residual stress management in thin films by using the focused ion beam.Science and technologyKi-Ju Kang, Darzens, Severine, Gee-Seob Choi
Effect of strain path and the magnitude of prestrain on the formability of a low carbon steel: on the textural and microtextural developments.Science and technologyYerra S.K., Vankudre, H.V., Date, P.P., Samajdar, I.
Elastic stress concentration of an ellipsoidal inclusion of revolution in the vicinity of a bimaterial interface.Science and technologyNoda, Nao-Aki, Moriyama, Yasuhiro
Electron transport in deformed carbon nanotubes.Science and technologyLiu, B., Johnson, H.T., Huang, Y.Y.
Equivalent time measurement model for physical aging and temperature effects on polymer creep and relaxation.Science and technologyBarbero, Ever J., Ford, Kevin J.
Fatigue crack initiation behaviour of welded AA5083 in a seawater environment.Science and technologyBakker, Ad, Janssen, G. C. A. M., deWit, Hans
Finite element evaluation of the remaining mechanical strength of deteriorated cast iron pipes.Science and technologySeica, Michael V., Packer, Jeffery A.
Formation of microscopic voids in resin transfer molded composites.Science and technologyHamidi, Youssef K., Aktas, Levent, Altan, M. Cengiz
Fracture toughness of highly ordered carbon nanotube/alumina nanocomposites.Science and technologyCurtin, W.A., Xia, Z., Sheldon, B.W.
Fundamental mechanical properties of carbon nanotubes: current understanding and the related experimental studies.Science and technologyYu, Min-Feng
Influence of carbon content in cobalt-based superalloys on mechanical and wear properties.Science and technologyLiu, Rong, Yao, Matthew, X., Wu, Xijia
Influence of extra coarse grains on the creep properties of 9 percent CrMoV (P91) steel weldment.Science and technologyWu, Riu, Sandstrom, Rolf, Seitisleam, Facredin
Interfacial structure and micro and nano-mechanical behavior of laser-welded 6061 aluminum alloy blank.Science and technologyMing Li, N.Q. Wu, Cedrix Xia, Perrusquia, N., Mao, Scott X.
Introduction to compressive residual stress using a cavitating jet in air.Science and technologySoyama, Hitoshi
Investigation of fracture in transparent glass fiber reinforced polymer composites using photoelasticity.Science and technologyKhanna, Sanjeev K., Winter, Robb M., Ellingsen, Marius D.
Measurement and microstructural evaluation of creep-induced changes in magnetic properties of a 410 stainless steel.Science and technologyPolar, A., Indacochea, J. E., Singh, V., Lloyd, G.
Mechanical behavior in the silicon carbide reinforced aluminum 6061 composites degraded by room or high temperature 3.5% NaCl solution.Science and technologyAhn, J. J., Ochiai, S.
Mechanics of axial compression of single and multi-wall carbon nanotubes.Science and technologyBoyce, M.C., Parks, D.M., Pantano, A.
Micromechanical simulation of dynamic fracture by using the cohesive finite element method.Science and technologyJun Zhai, Tomar, Vikas, Min Zhou
Micromechanical simulation of dynamic fracture by using the cohesive finite element method.Science and technologyTomar, Vikas, Zhai, Jun, Zhou, Min
Modeling cyclic deformation of HSLA steels using crystal plasticity.Science and technologyGhosh, S., Xie, C. L., Groeber, M.
Modeling of fatigue crack propagation.Science and technologyJiang, Yanyao, Feng, Miaolin
Observations of the constitutive response and characterization of filled natural rubber under monotonic and cyclic multiaxial stress states.Science and technologyMars, W.V., Fatemi, A.
On hydrogen-induced void nucleation and grain boundary, decohesion in nickel-base alloys.Science and technologyLiang, Y., Sofronis, P.
On identification of material models when nonrepeatability of test data is present: Application to textile composites.Science and technologyMilani, Abbas S., Nemes, James A.
On the characterization of fatigue crack growth in a plate with a single-sided repair.Science and technologyDuong, C. N., Wang, C. H.
Practical methods for the design of sheet formed components.Science and technologyGan, Wei, Wagoner, R. H., Mao, Kunming, Price, Shane, Rasouli, Firooz
Predicting the effects of overloads on fatigue crack growth in an AI-Sic MMC using a computational model.Science and technologyBruzzi, M. S., McHugh, P. E.
Prediction of Brinell hardness distribution in cold-formed parts.Science and technologyDemir, Ahmet, Sonmez, Fazil O.
Procedure for the determination of true stress-strain curves from tensile tests with rectangular cross-section specimens.Science and technologyScheider, I., Brocks, W., Cornec, A.
Size effect on flexural strength of fiber-composite laminates.Science and technologyBazant, Zdenek P., Young Zhou, Novak, Drahomir, Daniel, Issac M.
Static and dynamic analysis of carbon nanotube-based switches.Science and technologyDequesnes, Marc, Tang, Zhi, Aluru, N.R.
Tensile deformation and rotating bending fatigue properties of a highelastic thin wire, a superelastic thin wire, and superelastic thin tube of NiTi alloys.Science and technologyMatsui, R., Tobushi, H., Furuichi, Y., Horikawa, H.
The effect of nanotube waviness and agglomeration on the elastic property of carbon nanotube-reinforced composites.Science and technologyGao, Huajian, Shi, Dong-Li, Feng, Xi-Qiao, Huang, Yonggang Y., Hwang, Keh-Chih
Thermal expansion of single wall carbon nanotubes.Science and technologyLiu, B., Jiang, H., Huang, Y., Hwang, K.C.
Thermal shock strength of a semi-infinite piezoelectric medium.Science and technologyWBao-Lin Wang, Yu-Guo Sun
Thermo-mechanical modeling of hot forging process.Science and technologySerajzadeh, Siamak
Through-thickness residual stress distribution after the cold expansion of fastener holes and its effect on fracturing.Science and technologyOzdemir, A. Tamer, Edwards, Lyndon
Transverse-isotropic elastic and viscoelastic solids.Science and technologyFreed, Alan D.
Tribological behavior of aligned single-walled carbon nanotubes.Science and technologyYang, Wei, Ma, Xinling, Wang, Hongtao
This website is not affiliated with document authors or copyright owners. This page is provided for informational purposes only. Unintentional errors are possible.